It seems the spring on my 510 connector has come off. I have the spring. Is it any type of way I can fix it? Or an I screwed?
So, here's the deal. My new mod was delivered today. I knew it had a fixed stainless 510 connector, but I wasn't worried. Anyway, I'm not sure what I am doing wrong, but the tank keeps coming loose on the mod. I know I am probably not cranking it down tight enough, but I am afraid of going too tight and screwing up the threads.
So, I am looking for an adaptor that has a spring loaded pin on both sides. Spring loaded on the battery side and spring loaded on the atty side. Is there such a thing? I would also prefer that this is 22mm wide. Any ideas?
Some people build and drive them. Others do this:
400w 80A Delta - Imgur
Specs:
80A/400W Delta Delphi DC/DC Converter with custom designed breakout board
Red Powdercoat Diecast Aluminum Hammond 1590BBS and N52 Magnetic Door
IRLB3034PBF MOSFET switching
Venom 3S 40C 2200mAh LiPo Battery Pack with XT60 connector
Low Profile FatDaddy v4 Spring loaded 510 connector
The width and thread size of the 510 connector is standardized, but why is the length not?
I tried my best to understand why not from a design or engineering standpoint, but I can't work it out. Not only would it make life simpler when changing attys. But it would eliminate screw and spring loaded 510 pin adjustment, and all the the issues associated with them.
Any ideas anyone?
The Seasonal Sales Suppliers forum is once again open for our ECF suppliers offering specials over the next week for Spring & Easter sales!
Come on over and check it out !
Spring- Easter Sales 2015!
Note: This holiday sales Forum will be closed April 8th, 2015
-------------------------------
Don't forget to visit ECF Supplier forum for our ECF Suppliers' regular advertising threads and contests
E Cigarette Suppliers Forum
Molicel 18650s are ever so slightly bigger than samsungs. I found this the first time I popped a couple in my mod. The fit was a little bit tight. Now as this applies the the legend, the battery door being on the bottom and spring loaded, it's a bit of effort to close it. Not a deal breaker but i just need to make sure its closed securely. Now, lol, this morning I put in some freshly charged batteries, closed the cover and set it down only to have the door pop back open. The spring on this door was strong enough to flip my mod over when it popped open. Its probably only funny if you were here an saw this happen.
Begins now.
I've had a TC mod for abit but never usedthe TC.
Then a guy at work got an Invader and I used it. Its nice.
So off to Temco for wire.
Not really gonna mess with it today but I wrapped a quickie. Its more of a spring then a coil but thats what they say.
I have almost all dual coil tanks and I'm not there yet so I grabbed a Taifun and installed the "spring".
Wow. This is pretty amazing. The flavor is unreal. I only vape one thing so its the same juice but I'm like one of them wine guys. I can taste traces of wood fired oak cask in the VG and I can pick out each of the five flavors in the citrus mix. The menthol, which is perfect is now maybe abit much.
If we assume my tenth coil will be perfect I gotta say this is a great way to kick off 1-9.
My charger has those eeh springy slides to keep batteries tightly set.
Couldn't find a respectable charger without them.
How do you avoid damaging the battery wrap when inserting/removing in a charger?
Inserting a battery is easier as you can preload the slide with a finger.
But when removing a battery the spring slide eats into the battery wrap on the way up.
Would be nice to avoid any wrap damage.
Maybe put a rubber band / twine / other (non-conductive) underneath so it can be pulled and open the spring slide after charging?
Like a slingshot
Other ideas?
So I've been using a Kayfun v4 and provari p3 using the hybrid connector and have never been able to get th ohms below 2 using .2mm guage kanthal bought from Vape escape one 2 mm coiling tool and about 6 wraps was initially happy with that but after reading the results other users are having they typically end up around 1.2 1.4 ohms using far more wraps then I have been using I tried to increase my coil diameter to 2.5 mm and the ohms exploded to 5 ohms making it unusable I have noticed that my spring in the Kayfun gets incredibly dirty and charred with what I can describe only as soot if anyone has any insights into what could be going on I would much appreciate it ive been enjoying my Kayfun but I'm still looking for that mind blowing Vape I keep reading about
I still cannot find it; as all my mods stop firing. Right now I'm using my first mod.The K100. It outperformed all of my other mods that I had before they all took a poop on me. Its crazy. Could it be the spring, that makes it so good? I have no idea. I tried the tugboat mod, it failed me. It stopped firing after a few days. And that thing hit like a champ. But this k100, seems to be knocking me out. Like taking a uppercut from Chuck Liddell. I just want to know if there's a magnetic k100 type mod, or should I just stick with this? ( I hate the way it looks BTW. Cause all I have is black rdas. )
I'm looking for an inexpensive box mod to carry around and wanted to know what everyone's opinion was.
I'm looking for something fairly small, spring loaded pin, removable battery... And looks good lol
So i'm looking at the smy 50w right now but wanted to get some other opinions.