Noop Tip O Rings

Yea yea E Juice I know


But... still ...

Nothing petrolium based as that can kill ya ----- ok so no chapstick

but how about burts bees wax isn't that all natural and ----ok to lube my O Rings with ??

http://www.e-cigarette-forum.com/forum/general-vaping-discussion/654241-noop-tip-o-rings.html  

I do know where I can get o-rings for my technical needs (oil resistant, heat resistant, etc.), but I have now idea where to get FDA approved o-rings suitable as spare rings for tanks.  

Now that most of the stocking up is behind us, what would be a suitable procedure for maintaining items in storage?

For regulated mods, keeping them dry is probably all that is needed. But should the sealed wrap be removed to avoid condensation inside?

How about atomizers? I had a problem in removing the cap from a used RDA after it was in storage for two years. Had to resort to using WD40 because the o-rings became adhered to the metal surfaces. I ruined the o-rings in the process. Would it make sense to go through and disassemble/reassemble things at certain time intervals? Should items be stored disassembled? Will o-rings become permanently compressed over time? Maybe put some vg on the o-rings for storage? Or should o-rings be removed? It's already been said that things should be cleaned/soaked before going into storage.

I have one RDA that gets sticky while in use. I remove the cap about once a week, just so I can.

What do you do? What do you think?  

The Tank He Gave Me Is A SMOKE TFV12 Prince Tank:
And it came with what appears to be green O-Rings (2 of them) about half an inch in diameter does anyone know what these are for? Aside from the color, they look like the ones pictured below. (I know what the white thing is used for it's the O-Rings that I am not sure about). ​

(The manual didn't tell me and I went onto the company website where it said the full manual was but couldn't find it.)

 

I just watched a review for this new RDA, and I'm very interested. Has anyone used/bought one yet? RT had issues with the o-rings failing which a cause for concern, but other than that it looks awesome. Lots and lots of airflow options.

Manufactured by Sparkle Technology which appears to the 'authentic' subdivision of Infinite, a well known producer of quality clones.

Features:
12 different adjustable airflow combinations. 22mm diameter. Copper adjustable 510 connector. PEEK internal AFC rings and base for optimal thermal regulation. Engineered to create a vortex inside the chamber. 303 grade stainless steel. Solid three post setup for durability on dual or single coil builds. Posts are squared for even better reliability.

 

So I recently gifted a friend of mine who is still getting his feet wet in the vaping world a Kangertech Aerotank Mega, and for some reason, he thinks you can fill it from the top, which I told him you definitely can not. I'll post the exact conversation here.

Him: you can do that with the Aerotank Mega too
Me: You can? I don't know about that.
Him: yeah but you have to be careful how full you fill it, of course.
Me: No. It's a bottom fill. The only way you could fill it from the top is if you only do it like halfway, due to the chimney being the way it is.
Him: then the mouthpiece part shouldn't be able to come apart from the tank, but it does, it's not even glued together.
Me: Yeah. That's called a drip tip. They're interchangeable. Your T3D is like that, too.
Him:
yeah, but with the T3D it's a seperate part that comes off, and doesn't leave the top of the tank exposed.
on the aerotank mega it's all one piece. either way, you can still only fill it so full from the top or bottom because of the center hole. it still holds a good amount though.

So, yeah. I'm pretty sure the only way you could possibly fill it from the top is if you took the top half of the chimney off and filled it that way, since the chimney is kind of in two pieces, but then you could only fill it to the spot where the chimney splits. Anyone who can definitively settle this for me?  

Hey. As the post states Im trying to decide what online store to buy my next purchases from. Im looking at buying a few different things. It is basically a new start into the world of rebuilding.Both RTA and RDA. Maybe a regulated device or mech mod, but Im more concerned with tanks and attys. I also need to purchase a few rebuilding tools.

Here is what I have so far and where Im headed:
Already have Kanthal A-1 26 and 29 gauge wire. Also have Koh Gen Do Cotton. Also have tweezers, clippers, pliers, scissors,etc. Basic stuff. My setup is iStick 30w and Nautilus Minis.

Looking to get:
1 or 2 RTA's (almost certain on Kanger Subtank Mini)
1 or 2 RDA's (possibly Magma)
Coil Jig, Screwdrivers, spare parts such as o-rings, etc
Any other useful things not already listed. Not opposed to authentic or clones. But im not gonna spend a small fortune

As far as websites are concerned Ive looked at Fasttech and Focalecig alot. Leaning towards Fastech but really dont want to wait a month ...

ANY HELP WITH BEST WEBSITES AND GEAR WOULD BE MUCH APPRECIATED.

Thank you guys always  

It ain't me... it's my cat begging me to make O-rings... Then she stares at it like seeing something for the first time and try's to catch it.

I'm a bit worried for her and the pg levels in the juices. I guess we are all "sinners"/stupid/idiots and do something that shortens our lifes...

Perhaps i should buy another tank/dripper with only 100% vg juice, just for the cat... lol..  

Hi vapers.

So I wanted to change out the o-rings on my Crown IV tank as it has a bit of a leak when it's almost empty....

However, I can't figure out how I'm gonna get this o-ring out.
Any tips ?


​
Any ideas are much appreciated ! Thx !

EDIT: Got it out with a tiny dab tool !



 

Just curious....I love the clone/ authentic threads. People get pretty "passionate" about what other people choose to spend their money on....its kinda crazy.

I was just curious if anyone ever changed their stance on buying or not buying clones after reading one of the thousands of angry debates about clones vs. authentics.

My stance has remained steady since the beginning. I still don't care what you use.