Coil Testing Results

Hi. I have just purchased the heavy hitter mech mod.
The coils I bought are wotofo .28 dual core fused claptons.
It is a asgard mini RDA, it will be a dual coil build , so resistance should be .14
Will a Samsung 40t battery be ok with this build.
In regards to saftey and amp draw.
Thanks  

Hey everyone,

So I've had the crown 4 tank for about 6 or so months and switched to mesh coils a couple months ago, off and on. The reason being is that it seems with the 4-packs I've bought, it's almost guaranteed that 2 will be either VERY picky about how tight i screw the tank and coil on the base. It has to be JUST tight enough where the box gets an ohm reading, but any tighter it looks like it shorts out (the ohm reading blinks 0.00). I've never messed around with the coil before, i usually just end up going back to the traditional coils and dealing with the lacking taste. Any suggestions? I'm using the sub box mini v2 if that makes a difference.

Thanks!  

I'm new to RDA's, I have a Cloud werks RDA. I'm using a GeekVape aegis solo, I put in 1 0.45 ohm Alien Clapton 32gauge A1 coil, not sure if I can put 2 coils in. Anyway I have tried 50W to 100W and get very very little vape out and absolutely massive spitback (burned the F out of my tongue). Can I install 2 coils in this tiny RDA? I need help something is really F'ed up.  

I have an MFeng UX that have temp control built into it and I have a crown iv tank that has stainless steel coils with it out of the box. I tried the tank on an IStixking 530 mod with coil set to stainless, I tried a tcr of 0.000093(I think?) And kept the temp below 400. The Sticking said no juice detected, I looked it up, some people were able to use nickel and it work good. The coil died fast, and I wanna learn how to use temp control without ruining the other coil. Basically, I wanna use it on my mfeng, and not guess at what settings lol. Any advice?  

So I built a twisted build out of nichrome 60 wire and tried it on a triple series 18650 mechanical box and it melted the coils why won't nichrome work with any series boxes 8.4 volt melted 12.6 volt melted but I can build a .06 nichrome build and run it on my mech tube mod and it handles it I can build .15 and run it at 150 watts on my Sigelei and it handles it but bump up the voltage and it melts don't get it. I ran a .30 nichrome build at 260 watts on a SMY 260 and had no failure of the coil so I'm puzzled why a series mech box desemates the coils?  

I am trying to get the best flavor with the best single coil build.

Objectives:
Flavor Smooth Vapor
Materials:
Kanthal Wire 35mg Nic Salts
I have noticed that either depending on the diameter of the coil or the spacing of the coil wraps You get a different kind of vape hit. It seems like higher gauge wire produces a smoother hit. And then couple that with a small diameter coil build, plus squishing the coil together to remove all coil spacing results in the smoothest possible vapor.

Can anyone confirm my findings? Or does anyone have any tips because I have still to replicate the smooth hit from clearomizer sub tank cartridge's that are non mesh. I am starting to think this is because the cotton is wrapped around the outside of the coil instead of being shoelace through the middle of the coil.  

I've been using Smok Stick M17 pen for years. They usually cost me $18 each. However, they have been discontinued.

I would get a pack of 5 coils (0.6) for $8-$12 and "HEAVY" vape and a coil would last me 7-10 days on average. I would buy 2 pens at a time and they would last several months before they would no longer charge anymore.

I'm down to one pen still working and two coils. I can still get coils but pretty sure the pen is going to fail soon.

Has anyone been in the same situation and know of a good replacement? My main concern is finding something with a similar coil cost and how long they last.  

I have been using an evod for two years now. Yeah, I know, minor leagues, but it gets the job done just fine for me.

For the first 18 months I was constantly buying new coils. I work from home so I can basically vape all I want and I vape A LOT. I use Swagger as my ADV and it will destroy a coil in just a couple days. It was becoming difficult to even find coils to buy and it was getting expensive, so I did some research on rebuilding my own coils. At first I tried to build them with silica wick, but I could never get them to work right. Using 1mm silica wick wrapping around a stick pin the wraps would always be too big and there was lots of leak/gurgling. So I went the cotton route and would wrap around a 1/32 drill bit and then slide the cotton through the coil. Works great, perfect ohms, great flavor. I've been doing this for the past six months. In the first 18 months of vaping I never got sick once. Since I've been using the cotton wicks I've been SEVERELY sick twice (probably a respiratory infection but never went to the Doc), and now I feel like I'm getting sick AGAIN.

I've noticed that I can see little flecks of what looks like cotton building up on the mouthpiece, and I'm assuming, going into my lungs. I think this is what is making me sick--the buildup over time. Anyone else had issues with this? I think I may have reached the end of my rope with vaping and now maybe I'll do what my original intention was (quitting altogether after vaping for a short period of time).

Anyone have any tips on rebuilding coils with silica? I've watched a million Youtube videos and replicate the process perfectly, but the wraps end up being twice the size they should be and I've been unable to slide silica wicks into the coil like I do with cotton because even at 1mm it's too big to fit through the hole. Thanks for any help.  

I am kinda a noob when it comes to prebuilt coils. I am looking for coils that feel very strong/sturdy, but I am not sure what material it is.

I had coils that said they were .25ohm and all it says is "KA1 WIRE + Ni80 wire" and they felt very sturdy/hard to pull the wraps apart etc....

I bought what I thought were a good replacement for those, but they feel flimsy and easy to pull apart the wraps. They are .36ohm, 316l stainless steel, 30gx4/36g.

So apparently the stainless steel wires are more flimsy...I cannot seem to find coils that have KA1 + Ni80 like the sturdy coils I once had. I
am trying to figure out which material/what I need to look for in order for the coils to be sturdy like the old coils.


Can someone help me out with this? Thanks in advance.  

So i build my coils, but i wanted someone get my wraps tighter, so i asked a friend, and he recommended me too one of our vape shops. the guy there said $5 per coil and 5 for wicking, is this just outrageous or whats the normal price for a build