Why Does It Go To 50 Watts?

I've been using only twin-18650 mods for some time, and before the shipping ban came into effect, I bought a backup of my most-used mod (a Geekvape Aegis X), but since the 100W single 21700 / 18650 Voopoo Drag X Plus was only $35, I also picked up one of them as another backup.

I vape exclusively on RDA's, typically with a 3mm dual coil twisted build with 24 or 26 gauge Kanthal or nichrome-80. 5 or 6 wraps with 24 gauge, 6-8 wraps with 26 gauge. I typically vape these between 90 and 110 watts.

I did not expect to get a 'true' 90-100 watts out of the Drag X, so I set a target of around 60 watts. I mounted a 3mm dual coil twisted 28 gauge build with 6 wraps, which on my Aegis X vapes great at 60 watts, and very good at 50 watts. It measures at 0.45 ohms.

But on the Drag at 60 watts, it only vapes at what feels like 30 watts on my Aegis. Setting it higher makes no difference either, it seems to 'top out' at ~30 watts regardless of the setting. 60 watts @ 0.45 ohms is only around 11 amps, so I doubt I'm hitting an amperage limit.

I am using 18650 batteries (VTC5A), and it is about time to replace them, as I am only getting around 70% the battery life as I did when new. I will be picking up some 21700 batteries at the same time, which hopefully help with things on the Voopoo.

Does anybody have any good experiences with ~60 watt builds on a Drag X Plus?  

so in my pursuit of vaping above 200 Watts I made a fuse 3x24ga gauge wrapped with 36 gauge and I tried three coils. it came out .07 I Vaped it at about 375 watts it was a hot vape but the ohms were very low so I had a problem with power my DNA 250c was reporting 65 amp output so I took that and put in dual fuse 22ga gauge wrapped with 36 gauge I ran that build triple coil I used it at about 250 Watts. what I am trying to do is vape at about 300 to 400 watts with an ohm or .2 to .3. the inner diameter will be 5.5 or 5 mm I'll be using the kanthal core wrapped with 36 gauge and ni80.I'm trying to figure out what my next bill should be to try to vape above 300 watts the restrictions I have is it can't be below point 1 ohm or above .3 ohm I have two aromamizer plus has with the series deck The parallel deck a second parallel deck and a single coil deck. The single coil deck fit 6.36 mm.

I also have the aromamizer titan.

What gauge would you Clapton?

Sent from my HD1907 using Tapatalk  

My first .5 OCC coil only lasted 3 days . I put my device up to 25 watts and it totally fried it. A terrible burnt hit. I backed it back down to 20 watts and it was fine for a little while, but then another bad burnt hit. Down to 15 watts and I literally sucked hot particles in my mouth when taking a hit. ...? The cotton and/or coils are literally breaking apart? That's totally gross and I can only imagine, not that safe.

My second .5 OCC, I never put my device above 17 watts, keeping it at 15 watts for the most part. Within 4 days, same thing ... total burnt hit one day, sucking up hot particles the next?

What's going on? I thought I was supposed to be able to hit a .5 coil up to 30 watts ... Is sucking up hot particles from the coil normal? Should I just keep it at 12 to 15 watts and that's it, taking 1 to 2 second drags and that's it? Is it just a string of bad coils?

Thanks

EDIT: Thought I should mention that the juice I used for both coils was 50/50 watermelon. I hear it's better to use higher VG liquids with sub ohm tanks. But can that be part of the reason why the coils are being fried so quickly?  

Hello Been vaping about 2 years now
My setups are Vaporshark Rdna 30 Istick 30 watt and a provari 2.5 and a IPv mini v2 30 watt
So like many others I have been juggling with wattage I currently Use A couple of kanger subtank minis using the RBA and a kayfun v4 I've been all over the place building ohms but have settled on 1.2 - 1.4 ohms BTW I'm not into sub ohms
So after many months of different ohms and watts with the help of steam engine I have found I like my vape at a heat flux of around 175 so to get to this and I can't believe how simple it was I just take the ohms I am using such as 1.2 @ 12 watts = 178 heat flux 1.3 @ 13 watts = 178 heat flux and so on I can't believe it became that simple
So I suppose all it takes is to find what heat flux you enjoy and adjust from there
I never bought that what I have read thru the last 2 years that 14 watts is 14 watts no matter what ohms you use it seems to me there had to be more factors involved
Just my thoughts


Sent from my iPhone using Tapatalk  

So I decided to try a 1,6 ohm coil on kayfun v4 clone Tobecco and I am using 28gauge Kanthal with a cotton
wick on a Rdna 30 and its vaping well at 15 watts I have a kanger subtank mini coming in the mail and here goes my question
So the kanger subtank states that with a .5 ohm coil i could vape up to 30 watts but the voltage comes in at like 3.8 volts
I was under the impression that the rdna 30 needs at least 4 volts to work which kinda brings me to my second question
What is the point of of sub ohms? cant i just build a 2.0 ohm coil or something like that to achieve the results as if i was subohming
I am very confused on this
thanks for the replys in advance
Oh yea is a 1.6 ohm coil at 15 watts a normal build or any recommendations for the kayfun v4 for watts and ohms thanks again  

I have a new istick 30w that I use with a smok micro adc2. I've used it with a new 2 ohm coil at 8 watts and is great. I changed to a used coil I had cleaned and things got weird. It's a 2 ohm coil and the istick is reading it at 4.9! At 8 watts the throat hit was too much so I went down to 6 watts. According to the manual the istick doesn't even fire to 4.9 ohms. So let's see what you got?  

a few little questions. I actually like dripping my 3 mg nic in max better even than vaping. I drip using 3 mg nic on a Istick 50 watt set about 23 watts with a draw of about 2.5 seconds and the coils reading says 1.6 ohms and the air holes blocked a tad on the el diablo bael. I vape on the Istick 20 watts somewhere around 7 to 8 watts on factory coil of 1.8 in a nautilaus mini
my questions: 1) does sub ohm in a rebuildable tank give flavour similar to a dripper
drippers seem to require higher watts is this in anyway suggested as less healthy ( I am not too concerned about the increased supposed formaldehyde issue I believe Dr F had issue with the research and in my opinion I probably breathe more formaldehyde off gassing wandering around carpets and insulation and pressboard)
2) the nic level is quite a bit lower in the dripper Does this actually translate to a drop in nicotine/contine levels in my blood in other words would I need to drip more to keep my nic levels somewhat reasonable re setting off " the I want a smoke brain run"
3 if I were to drip only for 3 or 4 days am I likely to find my 12 mg vape to strong

thanks for any insight you might provide  

I find keeping the voltage at 4.2 to 5 max will give me the perfect vape.It works out too using ohms law.For ex:,if i wrap a coil at 1.5 ohm,i set the watts at 12/13 and it works out too 4.2.

If i do .20 wrap i can ''bump'' up the watts to 50 and it will still be about 5 volts with no burnt taste.

Ya cant break ohms law.  

The 65 watt M65 I got is defective. So I'm returning it and replacing it with a new mod. But I'm stuck between 2 mods. The Smoktech X-Pro M80, or the Vape Connexx 150. Both look great but I'll give you a quick run down on the pros and cons of both.

Smoktech M80

Pros - 4400 mAh built in battery, 80 watts max power, .2-3.0 ohms, pass through vaping, decent sized and stylish.
Cons - only 80 watts, built in battery, 4400 mAh.

Vape Connex

Pros - like the bulkyness of it, huge firing button, 180 day warranty, interchangable 18650, magnetic back, .1-3.0 ohms.
Cons - no pass through, never heard of the brand.

So should I stick with a brand I know? Or risk it and get a really powerful mod? Any input is appreciated. Thanks y'all.  

Hello, I have been vaping for years, at 1.8 nic strength. I have some questions.

First of all I think I've made a problem by vaping on (all kangertech devices and coils), at .5 ohms, but I only vape at 20-24 watts. Is this wrong? Anything higher is way too hot, and I just don't enjoy it. I've bought a smok mag and other devices that wont fire under anything 50 watts and it was way too strong so I never use it.

Also, over the past 6 months I've developed some mouth sores I'm pretty sure it is
Tobacco Stomatitis
I know this is from vaping or smoking, the heat I guess is causing this. I've told my dr. about this he never really looked (I was in for something different than this), he replied try to vape point it downwards towards my tongue and I have been doing this for months, but to no avail with the mouth sores going away.

I can't quick vaping. I tried for a few days and I smoked more cigarettes than I ever did. It was actually hotter I noticed. I still smoke cigarettes when I drive, just a weird habit and at work on breaks. I vape all day at work when my boss isn't around.

I'm going to stick to just the unflavored e juice from now on. I'm also cutting the strength back. I also tried cutting it before with 0% percent e juice and to no avail my mouth sores are still there.

Sorry for the diatribe but I just have a few questions.



Does smoking at 22 watts and sometimes below with sub ohm coils, is this bad? I've been doing it for years now. The problem is I bought a ton and I find it hard to find coils now over 1 ohm. It seems all they sell not days is .5 coils. And I've tried nickel and and they just burn in a day, even with the settings they are supposed to be at, so I'm really at a loss as to what to do.

Also has anyone else experienced the tobacco stomatitis as I have?