Best/cheap Mtl Tank And Stock Coils With High Ohms?

Hello,

After vaping (sub-ohm) quite heavily for many years, I think it's time to quit that and switch back to MTL now.

What's the best/cheap MTL tank, affordable higher stock Ohms coils that use less liquid? I'll up my nic content to 12mg.


Thank you.  


Similar Content



Please Help Me, I Am Out Of Date.

I have been vaping for 4 years now. I am using the baby beast tank. I have 3 of them.
I have never used anything else because,, well, it works fine for me. My problem is that I am having a hard time finding coils. I used to by clone coils on ebay for dirt cheap. There are no longer any coils on ebay. I cant find any coils online. They are either out of stock; or very expensive. What do people do nowadays? Do people still use the baby beast or has everyone
changed to something cheaper/better? I always use Q2 .4 Ohm coils. I only found 1 place online that has them and they are $20 for 5 of them (including shipping). What would you guys do? I was so happy with the clone coils. They were inconsistent but cheap. Some would last 3 days and some would last 10 days; but for $1.35/each I was happy.
Thank you for any advice you can give.
MrElder  

Xpro M80 Plus Keeps Changing Ohms Reading On Each Puff...??

I have the Smok xPro M80 plus and I have a couple Kanger subtank minis I use with it. I usually use .5 ohm coils. Sometimes it will show the ohms fairly correctly at .54 or even .61, which seems close enough. However, as I puff, the ohms reading will tend to change after every few puffs. Sometimes it will even say up to 1.5 or 2.0 ohms on the same tank coil! One tank seems to do it worse than the other, but the two I use now both will change quite often, and once in awhile quite drastically. It sometimes helps if I unscrew the tank and screw it back on, but if it isn't really tight, the ohms read are really far off from what they should be. I'm not sure if it is the tanks or the M80 plus that has the problem. When it reads really high, if I don't catch it before I take a puff, it is horrible and burny-dry, since it thinks the ohms are so high...

Has anyone else had this problem and/or have any ideas as to how it can be fixed??

By the way, I've cleaned the connections and everything thoroughly, so it's not that...  

Low Ohms Reading Coil/tank Question

GS Air coils/GS 3ml tanks.
I Googlefied this and Did see One place that said A worn out tank could make coils not last as long. (Sounds near fetched to me...)

Can an old tank start Causing premade coils to show Low ohms, like. 05 ohm?

I am pretty sure these are factory coils not FT copycats.
Bruce in Ocala, Fl  

Mvp 20 Watt Not Reading Ohms Right

My MVP 20 watt recently started to get a little wonky on me. I use 1.5 ohm coils in an aerotank but for some reason the MVP is readin it as 4.9 and sometimes even higher. Of course its not hitting right either. I know its not the coils because if i put that same tank on my MVP 2.0 it reads correctly. The MVP 20w doesn't do this all the time but today its been doing it all day. It won;t go below 5 ohms and sometimes its even higher. Is this thing shot?  

Rebuilding Kanger Heads , Help Please

I just Started rebuilding my kanger dual coils and im having a issue , seems like when i build them and check my ohms on my meter they are right where i want them but when i put them in my tank and fire them up the ohms fluxuate like crazy from low to high ohms, any idea why it happens ? It occurs even when i build single coils. Anyway to fix this? Thanks  

What Coils And Battery To Use??

I bought a Kanger Subtank and Atlantis V2, but sold them because they just weren't wicking my 100% VG liquid (Velvet Cloud & Gypsy eJuice) well at all. I tried using the atlantis with the .3 ohm coil installed at 70-80W, which was the stated operating range, and found it to be EXTREMELY hot. So hot that the tank quickly heated up to the point of almost burning my lips. The Kanger just burned the wick up at 20W+ with the .5 ohm coil, despite letting it sit filled for a few minutes and priming.

I am very interested in picking up a Royal Hunter, although I've no idea what pre-made coils (i dont want to make my own coils, just dont have the knowledge or time to learn how) and battery to get. VaporDNA sells UD pre-made coils in various resistances, but figuring out what resistance to use, and thus what wattage battery to get is where I am stuck. Not sure if it'd be better to run at lower ohms / higher wattages, or higher ohms / lower wattages. I'm not sure if it's possible to get massive clouds, but a cooler vape at the same time, but that's my aim.  

Why Do My Coils Die So Quick?

Hello everyone,

I'm vaping with a Vaporesso Swag and have tested the GT2, GT4, Mesh and Ccell coils so far. I'm vaping 50/50 VG/PG liquid with 3ml/mg nicotine. I always use the coils at the lowest recommended wattage, airflow fully open and my puffs are usually 2 seconds long at max.
Now my problem, I'm going through coils faster than others change their underwear. I'm on my third coil now for 10ml (!) of liquid.
I prime my coils and I let them sit in the tank for at least 30 minutes before I use them. I get muted flavor after maybe 5ml of liquid and it tastes burnt after 10ml of liquid. I've also tried different liquid brands and at least 20 different flavors.
So what am I doing wrong? I'm about to quit vaping because of the immense cost of coils I go through. I just can't figure out what I'm doing wrong.  

Having A Hard Time Finding The Right Set-up

I'm having a mad time trying to find a tank or clearo to fit a relatively small battery to upgrade from my triton without having to go to a MOD set-up I need a nice drip-tip too.It seems like an in between of my Triton tank and a MOD I can't quite find the vapor production I'm looking for I lowered my ohms on the triton 1.8 it did produce a bit more vapor but the tanks just aren't built for those ohms and they run to hot.I've already gone through three coils.I looked at the Aspire Nautilus mini premium kit not completely sold on it, eGo One battery with Nautilus mini but I think the tank I'm looking for should hold more e-liquid.Any help here much appreciated.  

Kanger Sub Mini Tank/ Dry Hits Help

Hey guys whats up. Well I had gotten the Sub Mini tank, the first tank I got was a dud. I had nothing but issues with it since day one. Coils went bad in 1.5 days both coils, then the rba deck was giving my sigeili issues and errors.

So I sent it back, They replaced it, and I now have Version 2 as they say. This tank has 2 air slots and different Holes in the tank. I used the Stock .5 coil but was just getting wayyyy too many dry hits.. So I went to the RBA deck, been using the coil that came with it, and I have 100% organic cotton. So I been using that, but now I am getting Dry hits with this thing!!! every 4th hit Is Dry!! I have to cover the holes and pull to get teh cotton wet again, and then 4th hit shes dry again.

What is going on here? Anyone else have issues like this? I am really getting fed up with this and ready to just throw it away. What can I do about the situation or why is this happening?

E-juice = 80/20 Clear Liquid all fruity flavors 3MG  

Upgraded My Tank But Still Tasting Liquid ??

Hey there guys, new here.

I have a Vappresso Revenger Mini kit and I have upgraded my tank from NRG SE Mini tank to a "Geekvape Z Sub Ohm tank(Much Larger Tank)". Because I wanted to taste more flavor and still blow lots of clouds in the air with my vaping device being fairly cheap.
I put a New Geekvape Z series coil 0.4ohm 50-60W because I burnt my original 0.2 Ohm coil , I wont talk about my previous coil. I'm getting 2 problems here.

1. I'm using 60W, normal setting and every time I vape or inhale I get a taste of E-Liquid in my mouth. However its blowing perfect clouds and still getting an amazing taste but its just that the liquid drops in my mouth. I just want to spit it out every time. How do I fix that problem?

2. The other thing is if I use Higher Wattage and High settings the liquid pours out of the air flow and starts leaking and backspits in my mouth.

(Before I vaped with new coil)I put the new coil in, I soaked it for 10-15mins, while I fill half tank of E-liquid which is 0.8Ng/0.2PG. Then I inhaled 3-4x with no button pressed. Then I vaped to test, still leaking. I set the vape to 70W and high setting then blow downwards into the device 5-6x. All I was trying to do is desaturate it. My results got better didnt notice much of a leak but I still get a little bit of liquid in my mouth. If you can help me out here, I would much appreciate it.

Thank you and kind regards

Tuatara Vaper