What Is The Maximum # Of Volts Can I Use With A 1.6 Ohm Coil?

I have a variable W/V battery and I prefer it on 4.2, but it is expensive and I never get the full 300 charges out of them like they claim they are supposed to get. Will decreasing the voltage by 0.4 Volts increase the battery life to a significant extent that makes it worth while?  

I've got a Nautilus with a 1.6ohm coil, and an iStick 50w. On the side of the coil it says 3.2v-5v, and I want to know if that's just a guideline or a limit for the coil.

I'm running it at 4.8 volts, but I get better flavor and vapor at 5.5 volts. There are no wicking issues or burnt taste at 5.5v, but I don't want to damage the battery or the coil. Any advise would be great thanks!  

I'm finding a 1.3 ohm coil to be to low for me. On my Provari, between 2.9 and 3.5 volts are OK. I haven't used this tank on either of my other two variable wattage regs, but I'd think it to be in the 6 - 7 watt range. It's time to re-wick the other tank or quit typing and do it already. I think I'd go for the former, but then I'd have to think about that. The other tank's coil I wrapped to about 1.7 ohms. My mech and me would be ever so gladder if that tank was fully operational again.  

I'm not quite sure what the difference is between operating in VV vs VW is. a worker at a B&M said I'll get more "performance" out of VW mode ... But in my mind Ohm's law rules. If I run my Atlantis .5 at 4.2 volts, that's 29.4 watts. I understand that I can up watts a bit without affecting the voltage reading (maybe it affects it beyond the decimal places the iStick 50 can display?) but am I theoretically squeezing any more performance out of the coil? I'll be honest and say that it only makes a difference when the wattage reaches the borderland between one voltage output and the next and even that seems to be very minor.

I hope that makes sense. IOW, if I like the vape at 4.2 volts, then am I actually gaining anything by upping wattage without changing voltage? My initial experiments tell me "not really," but the science part of my head wants a better answer. Maybe I'm missing something?  

Evic VT 60W by Joyetech PREORDER | Vape Street


eVic VT 60W PREORDER

ONLY $65 DURING PREORDER!!

Presenting the eVic-VT 60W, its new cutting edge technology of temperature control, embodying the concept of a healthy alternative lifestyle. eVic-VT features a super large OLED screen, supporting VT-Ti (Titanium)/ VT-Ni (Nickel)/ VW mode, and battery capacity of 5000mah.
The Variable Temperature (VT) brings out a different flavor experience with the change of temperature settings, not only improving the taste,but also saving battery and liquid consumption. eVic-VT is not your typical vape, it’s an evolutionary start.
Features:
Size: 47*25.5*85.6mm
Capacity: 5000mAh
Output mode: VT-Ti/VT-Ni/VW Mode
Temperature Range: 100-315℃/200-600˚F
Output Wattage: VT Mode:1W-60W
VW Mode:1W-50W
Output Voltage: 0.5V-8.0V
Resistance Range: 0.05-1.0ohm for VT mode
0.15-3.5ohm for VW mode
Color: Racing Yellow, Cool Black, Dazzling White
eVic-VT Visual Display:
VT-Ti mode/VT-Ni mode/VW
Wattages/ Voltages
Atomizer Resistance
Battery power/Puff/Time
ETA: Approximately mid June 2015  

vaparroos,

so here is a chart: http://i.imgur.com/6oraBGI.png

this charts says if i have a 1.2 ohm in my kanger subtank that i can vape at 6.0 volts at 30 watts and be ok, but i know that is not the case...

when i'm vaping at 1.2 ohm at 3.8 votls its ok, but i'm in the orange too...why am i still in the orange at 6 volts?

hope that makes sense...  

I am not sure where this should go but this was the best place I could see. Anyway I need a bit of help here it should not be too hard. I am look to build a dual 26650 variable voltage cordless power supply for electroplating small parts . I need to be able to vary the voltage from about a .5 volts to 3.5 volts if it possible average voltage about 2 volts I would like it to compensate as the battery runs down a bit don't have to perfect but just help it keep the voltage steady so it will need to have a volt meter I see those all over in the diy mech mods
So I want to use a dual 26650 battery sled
A 1 amp usb charger port
I need a project box big enough
digital volt meter
I would think a mosfet to vary the voltage with a potentiometer
resetting fuse
and I would guess A piece of that project board stuff with all the hole in it like a for building stiff like this on I can't for the life of me remember what they call that board I built small projects on this stuff when I was kid so that was some time ago LOL it just a board with lots a little hole in it it's a sort of a PCB

I have a basic idea for this thing but last time a built any kind a power supply it was in high school and I am 53 now so I am rusty as Hedouble toothpicks LOL. So I really use a bit of help from someone that is good with this stuff I am sure I can build it that not the problem is getting the right values and wiring diagram and finding sources for the parts I sure one I have a wiring diagram and the values I can google most of that stuff but tips pm someplace maybe you got stuff from that has good prices and don't take a 100 year to ship LOL

In the end this will be the power supply for a silver plating with I have hope to maybe add some little videos picture and stuff of it. this will be kinda fun and I want guys to see how easy and cheap it is to electroplate silver for your box mod so when I done with the power supply I will do a tutorial help fold out in return for help with this
I will be doing stuff like nickel silver platinum. even gold plating

Any help with this would be great if it works out maybe I can plate some small parts for you as a thanks  

I have a variable voltage/wattage battery and I have heard that some say charge it as often as you can this reduces stress, others say that's bad, some say a combination of long and short cycles but I don't know which is best. My battery's manual said get down to 10% but it doesn't measure it accurately (but I love these batteries so I don't want to change but they are expensive so I want to prolong their life span as long as possible even if that does mean charging them very often.) I do have two so charging often isn't an inconvenience for me if that's what I am supposed to do.  

If I take softer but longer puffs will I consume less ejuice than I would if I take harder but shorter puffs? Also, how much of a difference does the amount of volts affect the amount of ejuice used?
I use an ego battery and have 4 air flow options, I like using 4.2V (my coil is 1.8Ohms) and the max airflow but this is not only tearing a hole in my wallet its practically making it disappear.
I only need enough volts required to vaporize the nicotine that I want (I'm not sure but I believe I'm using 46MG/10Ml nicotine ejuice, if I upgrade to higher level nicotine ejuice containers will the power and/or airflow requirements go down?
Finally, if I start using the 1.6Ohm coil (the only other coil the Nautilus is compatible with as far as I know.) will that make a difference in power consumption required to get the same effect?  

Hey vapers.

Wanted to start a thread for discussing the DNA 250c chip, all of its features, options, performance, etc.

I started this threat to not only begin a discussion about the DNA 250c chip, but to also share something with new users that may prolong the life of their batteries.

With battery life, I mean the number of charge cycles it'll take before noticeable decline in performance, and general battery health. My advice of setting the cutoff voltage higher will shorten actual run time.

I've noticed that 'out of the box' the DNA 250c is set to soft cutoff the battery at 2.75 volts.
This results in a 3.00 volt reading on my charger when I get the batteries out.

This, in the opinion of many, is too low for batteries to go, and especially to remain there for any length of time.

So, I want to share with you how to change the settings so that your mod will cease using the battery at 3.1 volts, which results in your battery resting at a healthier 3.35 volts.

Here's how :


​
Click the image for a larger view.

Basically, in Escribe, go to Options, then User Interface, then Advanced. Select Mod tab, and then Battery tab. There you will see the 2.75 volt setting, and you should change that to 3.1 volts. Upload setting to device, and you're done.

The DNA 250c comes with a wide array of options and customized performance.

I'd love for people to chime in and share their tips and expertise with Escribe and the DNA 250c chip.

So let's hear t !

P.S. When will Evolv update Escribe to list 21700 batteries ?




​